Today I posted a major revision with many updates to my ebook, "Guns For Jews." It's now hosted as a PDF on my Google Drive. Direct link:
https://drive.google.com/file/d/1WgjlXp2sDGPYTpjNdskWqYQVwF380SlG/view?usp=sharing
It's my hope that this will be shared with as many of my fellow Members of the Tribe as possible.
The Tuff Products Quick Strips that I ordered the other day to use with my .32-20 Hand Ejector arrived today. They'll be perfect for packing reloads.
They can hold 8 cartridges each but I'll be loading only 6, which will give me a little more to hang onto while using. They also fit .32 S&W, .32 S&W Long, .32 H&R Magnum, .327 Federal Magnum, and 9x19. So, in the highly unlikely event you're packing a S&W Model 547 which is a 9mm K-Frame that doesn't use moon clips, these have you covered.
Today I took a vacation day and brought the .32-20 S&W M-1905 M&P to the range along with a couple other wheelguns.
L - R, the .32-20, a nickeled post-War M&P "pre Model 10", and a Taurus 856. The postwar M&P and the Taurus are .38 Specials.
The .32-20 has one of the heaviest trigger pulls I've ever felt on a K-Frame, but it's smooth in both SA and DA. Shooting DA from 10 yards I was able to keep my shots in the -0 zone of an IDPA target. Considering the heavy trigger and poor sights I'm happy with that. I shot it with two loads, a 96 grain RNFP on top of 3.5 grains of Bullseye, and a 115 grain RNFP on top of 3.2 grains of Bullseye. The 115s shot a little higher, as expected.
When shooting rapid DA the gun squirms a little bit in my hands due to the pre-Magna service grips, even with the grip adapter in place. I will probably install a set of Magnas just to make it nicer to shoot but of course I'll hang onto the original grips, which are serial numbered to the gun.
I was shooting indoors today under florescent lights. This always makes poor sights harder to see compared with shooting in natural daylight and today was no exception. The rear sight on the M-1905 is a small V-notch while the front blade is fairly narrow. The postwar M&P has sights that are easier to see.
Overall, the .32-20 is a very nice shooter and I'm glad I bought it.
Because I've thought it would make a nice woods gun I'd like a couple speed loaders for it, if for no other reason than as a convenient way to carry a couple reloads. I tried K-Frame .38 speed loaders but they don't hold onto the narrower .32s. So, after some googling, I found that the Tuff Products Quick Strips sold for use with .32 S&W Long, .32 H&R Magnum, and .327 Federal, as well as 9mm should work with .32-20s. I ordered tow of the 2 packs of the orange versions. Being orange they should be easier to find if dropped and will help me tell them apart from my .38/.357 Quick Strips at a glance.
The postwar M&P is of course a very nice shooter. Unfortunately it's has a grooved trigger that likes to chew up my finger so after a cylinder or two I wrapped my finger with masking tape. In contrast, the .32-20 has a smooth trigger which is better for DA shooting.
The Taurus 856 is a surprisingly good shooter with a nice DA pull. It's a little larger than a J-Frame and holds 6 beans in the wheel, like a Colt Detective Special (whereas .38 J-Frames hold 5). I have small hands and find the grips comfortable. It'll make a good carry gun loaded with .38 Special wadcutters.
Posts
