Ruger SR22 Deep Clean

Today I gave my Ruger SR22 pistol a deep cleaning. The last time I shot it I had several rounds which failed to go off on the first hit, but which went off on the second hit on the same spot on the rim. This isn't too unusual with .22 rimfire ammo but neither of the other two pistols I shot in the same session had the same problem. So, I think I was getting the occasional light strike.

First I field stripped the Ruger and cleaned the barrel, paying particular attention to the chamber. It had some build up in it which I removed with a bronze brush and Kroil. After I was done I pushed a few dry patches through the bore. The barrel is made from stainless steel and in my environment doesn't need any oil to prevent rust.

My final check for the chamber's cleanliness was to drop several rounds into it (Remington Golden Bullet, CCI Standard Velocity, and Aguial Super Extra SV). I tried with 2 or 3 examples of each and most freely dropped all the way in. A couple required a slight touch. I expect this kind of variance in .22 rimfire ammo.

The next thing I did was to detail strip the slide so I could ensure the firing pin channel was clean and dry, and that there weren't any burrs on the firing pin itself. To do so I used the instructions here:

https://www.rimfirecentral.com/forums/showthread.php?t=429069

If you remove the breech block from an SR22 slide, be careful. There are several small parts and springs. I dropped the firing pin safety and had to get on my hands and knees to find it.

While I had it apart I lightly polished the sides, top, and bottom of the firing pin on a gunsmith's stone.

After blasting it with solvent and then with compressed air until everything was dry, I reassembled it. To prevent any oil from migrating up into the breech block I removed what oil I had on the slide and rails, and put a small dab of white lithium grease on the slide rails before putting the gun back together.

I wanted to remove the lockwork from the grip frame but that pin was really stubborn and I did not want to really wail on it at this time.

It may be a week or two before I'm able to test fire the Ruger. I'm hoping for better reliability.

Twenty-Two Palooza

This weekend I got to the range with a few .22 pistols:

• Ruger 22/45 Lite
• Ruger SR22
• High Standard R-100 Sentinel

I'd recently remounted a Bushnell TRS-25 red dot sight on the 22/45 and it needed to be zeroed. It wasn't too far off at 7 yards so zeroing it didn't take long. However, my plan is to do the final sighting in at 25 yards. The piece ran flawlessly through a mix of CCI Mini Mags, Federal Game Shocks, and Remington Golden Bullets.

Next up was the SR22. The last time I shot it I had a few rounds which required more than one hit on the rim to go off. That's not terribly unusual with .22 rimfire ammo but the SR22 seemed to be a bit more prone to it, so I gave it as thorough a cleaning as possible with removing the breech block from the slide. Unfortunately, I had a few rounds which required more than one hit, both Federal and Remington. From what I can tell, the SR22 would benefit with a slightly stronger hammer spring.

Finally, I put a few different types of .22LR through the High Standard that I bought a week previously. These included Aguila Super Extra and CCI, both standard velocity, Remington Viper Hyper Velocity, and Remington Golden Bullets. 

Except for the final cylinder, I shot the Sentinel single action. It whacks the case rims with authority and I had no failures to fire. It seemed to give slightly better accuracy with the standard velocity ammunition.

I only put 9 rounds (one cylinder-full) of Vipers through the H-S. After a few shots the gun became more difficult to cock as the cylinder rotated. I think what happened is that on one round brass flowed back and was dragging. When I went to eject the empties it required a lot of force, unlike the other types of ammo. So, no more Vipers for that gun.

I really wish someone could design a small framed double action .22 revolver that would be reliable without a ridiculously heavy DA trigger pull. My medium-framed S&W Model 18 has a tolerable DA pull but if someone was able to come up with something smaller that reliably ignited rimfire ammo and had a similar DA, they'd have a real winner. And no, the Ruger LCP ain't it.

As an aside, I've had positive experiences with Remington Golden Bullet .22 ammo manufactured in the past 6 or 7 years. Overall in my experience, CCI has been the most reliable .22 rimfire ammo, but in the 5 years or so prior to their bankruptcy, Remington really improved the quality of their .22 ammo. I hope that now that Remington ammo is back in production the quality will be high.

My Remington 550-1 and Nylon 77 rifles both shoot Golden Bullets really well. Also, they are loaded noticeably hotter than CCI Mini Mags. I haven't shot any game with them but a friend gave up on GB hollow points for squirrels because they are too destructive. To paraphrase, "They blow the guts out."

Today I spent a little time playing with my Beretta Model 71 "Jaguar," and found a used factory 10 round magazine on eBay for the Model 73, 74, 76, and 101. These fit the 71 but stick out a bit from the butt. The price was about $70 but for a real Beretta mag it should be worth it. While I had the gun out I painted the front sight with a bright green. I've been doing this on many of my pistols because it makes the sight much easier to see.

Thoughts on Picking a .22 Handgun for the Lady of the House

Over on Bushcraft USA, the topic of picking a .22 LR handgun for a member's wife came up. The member's wife is adamant that she doesn't want anything larger than a .22. He was asking for input so I offered these thoughts:

First off, if at all possible get her to a gun store and let her handle a few different guns, to see which one is most comfortable for her. If you can rent some and shoot them, all the better.

Secondly, compact rimfire double action revolvers have hard trigger pulls which makes shooting them accurately much more difficult. This includes S&W J-Frames and Ruger LCRs in .22. (The one LCR I handled in .38 Special had a nice trigger.)
Thirdly, compact DA revolvers in general are tough to shoot well without proper training and a lot of practice. They are often recommended for women because they are small. But between the heavy triggers on the .22s and their general difficulty to shoot accurately -- which is doubly important with a .22 -- they are most often a very poor choice for the ladies, unless they have greater than normal hand strength and are willing to practice a lot.

Compact .22 autoloaders tend to have better triggers and are in general easier to shoot than .22 snubbies. They usually hold more rounds, as well. A good example is the Ruger SR22. I picked one up a couple years ago. My now-15 y/o daughter took to it immediately and shoots it well. It is a DA/SA semiautomatic pistol that uses 10 round magazines. It's very light and has a rail under the dust cover that allows easy mounting of a weapon light or a laser. Mine has been very reliable.

If relying on a .22 for defense ammo is critical for reliability. In my experience, CCI .22 LR is the most reliable. Bulk pack .22s give the most ignition problems. My choice for .22 LR defensive use would be CCI Mini Mag solids, for best reliability and penetration.
Keep the gun clean and properly lubed with particular attention to the firing pin channel, and feed it high quality ammo, and it will serve well for defense.

He also noted that she might consider a Ruger PCC Charger in 9mm, to which I replied:

If for some reason she won't go for the Charger version of the 9mm carbine, Ruger makes the 10/22 Charger. Setup as you suggested and with a Ruger BX-25, 25-round mag, that would make a formidable defensive weapon.

.22 LR is far from ideal as a defensive round but it beats harsh language and provides people who for whatever reason cannot handle a larger cartridge a means of self defense.

Saturday Night Range Report

Last night I hit the range with Dad and put some more rounds through the Ruger SR22 along with my CZ P-09.

I put around 75 Remington Golden Bullet hollow points, 100 Golden Bullet solids, and about 60 Federal 550 bulk pack hollow points through the Ruger. The gun didn't have any malfunctions that weren't related to ammo. To wit:

--Four of the Golden Bullets required a second hit to ignite.
--Three of the Federals required second hits.
--One of the Golden Bullet cases split and needed to be pushed out with a cleaning rod.

This batch of Golden Bullets seems especially bad. Previous range trips in which I've shot a couple hundred rounds of it had no more than one misfire per trip.

That's the most problems I've ever experienced in one range session with .22 ammo. When folks point to the unreliability of rimfire ammo as one reason .22s aren't suitable for defense (ballistics aside), this is what they're referring to.

In contrast, I've experienced exactly one misfire with CCI .22 rimfire ammo, among thousands fired.

The Remingtons seemed loaded hotter than the Federals, something I've noticed before. They also spit a lot more -- after virtually every shot I felt unburned powder granules on my face. I won't be using it when teaching my daughter to shoot.

I continue to be pleased with the Ruger SR22. The SA trigger is smoothing out, although the DA pull remains long, heavy, and has a lot of creep.

My round count through the CZ was much lower. I ran one 50-round box of Speer 124 grain Gold Dot JHPs through it as a function check. My dad also put 30 rounds of Fiocchi 9mm 115 grain ball through it. As expected, it worked fine. The pistol has over 500 rounds through it so far without any issues.

Dad brought his S&W Model 67 with some .38 Special 158 grain LSWC handloads and his S&W SW9VE, aka the "Smegma." The SW9VE is an economy gun but gets a bad rap because it isn't as refined as the M&P. Dad's has been trouble free for over 1,000 rounds.

More Range Time with the Ruger SR22

My daughter and I hit the range yesterday and brought along "her" Ruger SR22. I put 20 CCI SV rounds through it.  She shot it unsuppressed, so I had her use Remington Golden Bullet high speed brass-plated hollow points.

Golden Bullets don't have a very good reputation for quality but as of a couple years ago Remington seems to have improved them. They run well and give good accuracy in my Remington Nylon 77 and 550-1, so I wanted to see how the Ruger would handle them.

My kid put at least 150 Golden Bullets through the Ruger. We had one failure to go into battery that was resolved by bumping the back of the slide, and one misfire. After trying a second hit, then ejecting the misfire and rotating it 180 degrees, it went off. This isn't unusual with cheap bulk .22 ammo.

I'm happy to see the Ruger function well with the Golden Bullets. They were one of the few types of .22 ammo I was able to lay in a good supply of during the 0bama years.

Ruger SR22

I've recently been considering acquiring a second compact .22 autoloading pistol. A few years ago I picked up an Israeli surplus Beretta Model 71 Jaguar, which is a really nice shooter. However, factory magazines are unobtanium and if something breaks, I'm probably SOL.

This Father's Day I was given $100 in Cabela's gift cards, which I used last week towards the purchase of a Ruger SR22. The specific model I got is the 3604, which sports 3.5" threaded barrel.

About 5 or 6 years ago, Ruger introduced the SR22 which is a small DA/SA .22 semiauto pistol styled much like the Walther P22 (which in turn looks like a scaled-down P99). The Ruger has a much better reputation for reliability and durability, according to what I've seen online.

First some stats, then shooting impressions.

• Action: Semiautomatic, blowback, with double action/single action trigger.
• Safety: Combination safety/decocker
• Hammer: External
• Barrel: Stainless steel, 3.5" long with muzzle threaded to accept a 1/2x28 coupler*.
• Sights: Three-dot dovetailed into the slide. Rear is adjustable for windage and elevation.
• Weight: 17.5 oz.
• OAL: 6.4"
• Height" 4.9"
• Width: 0.97"
• Frame: Polymer with interchangeable grip sleeves.
• Slide material: Aircraft aluminum, anodized black.

From Ruger's North Carolina factory, the pistol shipped with a chamber flag in place, two 10-round magazines, two extra magazine baseplates to replace the pinky rests installed on the mags, a lock, the thread coupler, and a wrench for the coupler. A thread protector was screwed onto the barrel. It came off with moderate force using the wrench.

It also shipped with two interchangeable grip sleeves. Mine was fitted with the one that has a palm swell. I have fairly small hands and it fits me well. My 13 year old daughter also liked how the gun felt.

And of course, it came with an owner's manual, literature about the NRA, and a couple Ruger stickers.

Before shooting the Ruger I field stripped and lubricated it with some FP-10, since it was bone dry.

Field stripping and reassembly is straightforward. Certainly a lot easier than my Mark III 22/45 Lite. To field strip, unload the pistol, drop the hammer using the decocker, and then open the takedown latch in front of the trigger. The slide can then be pulled up and to the rear, off the frame rails, and then slipped forward over the muzzle. Note that the thread coupler has a flange around it that will prevent the slide from slipping forward over the barrel. If the coupler is installed it must be removed prior to field stripping.

The magazines are easy to load. Each has a thumb button to aid depressing the follower.

I haven't shot it for groups yet but did get a couple hundred rounds through it while plinking at a few old hard drives and a self-healing rubber target. The first 95 were CCI Standard Velocity rounds shot through my Form 1 suppressor. I also put a lone CCI CB Long through the can, which as you'd imagine was very quiet. The remainder were Federal Automatch high speeds shot unsuppressed. The gun had no malfunctions.

A primary reason for buying the Ruger was to get a pistol that my 13 year old daughter could comfortably hold and shoot. It excels at that and she's trying to claim it as her own after shooting it this weekend. Even with my silencer she's able to hold it steady and frequently hit our plinking targets. My next step will be to get her shooting at paper.

Incidentally, being able to shoot it suppressed is a major advantage when training a new shooter. My can is hearing safe when fired outdoors with standard velocity ammo. Being able to give instruction in a normal conversational voice instead of having to shout to be heard is damn nice. Contact your reps and let's get the Hearing Protection Act passed!

My initial impression, along with my daughter's and that of my friend who shot the SR22 are all extremely favorable. I hope to run a few more different kinds of ammo through it soon, and shoot it on paper to check group size and fine tune the zero (which is pretty much on already).
















*Most modern shooters insist that they be referred to as "suppressors." Their inventor, Hiram Maxim, named them "silencers." Under the National Firearms Act, they are "silencers," even if "suppressor" is a more technically accurate term.