Turning Components Into Ammo

Over the past few weekends I have been busy turning components into ammunition. I dipped into my stash of empty .38 Special brass and loaded up several different varieties:

• 50 rounds of 178 Keith semiwadcutters (SWC) on top of 3.8 grains of Unique.
• 50 rounds of 178 Keith SWCs on top of 5.0 of Unique.
• 100 rounds of 195 grain lead round nose bullets (LRNs) on top of a 5.0 grains of Unique.
• 100 rounds of 148 grain Lee tumble lube wadcutters on top of a 2.7 grains of Bullseye.
• 100 rounds of 148 grain Hornady hollow base wadcutters (HBWC) on top of 2.7 grains of Bullseye.
• 100 rounds of Speer 158 grain lead SWC hollow points on top of a 4.5 grains of Universal Clays.

DO NOT USE ANY OF THE ABOVE LOADING DATA WITHOUT VERIFYING IT IN ONE OR MORE LOADING MANUALS!!! I AM NOT RESPONSIBLE FOR ANY DAMAGE THAT OCCURS TO YOU OR YOUR GUNS IF YOU RELY ON IT.

The Keith SWCs, 195 grain LRNs, and Lee TL WCs came from Matt's Bullets. I ordered 100 count sample packs of each and was impressed with the projectiles. They are sized to .359 and loaded with Carnauba Red lube, except for the 148 TL WCs, which appear to be lubed with Lee Liquid Alox.

I was quite pleased with the service from Matt's Bullets, BTW. My order shipped in about a day and a half and was sent in a USPS flat-rate box. I received 2 days after I got the shipping notice. The bullets all looked good.

The Hornady 148 grain HBWCs have been laying around since I bought 1250 of them at the end of 2016. I've had the 500 count box of the Speer LSWCHPs for years.

So what prompted this binge reloading? First, the weather has been nice and it has been neither too hot nor too cold to work out in my backyard shop. Second, my gun interests go in phases and  something rekindled my interest in revolvers. It's been too long since I shot one of my K-Frames, S&W Model 28, or 50th Anniversary Ruger Blackhawk.

And frankly, the state of the political left in this country is really starting to worry me. As far as I'm concerned, they've been acting completely batshit crazy since Trump's election. I want to get in some more practice in case the left decides to take their attempt at a soft coup hot.

I was pleasantly surprised that the .38s loaded with the Keith SWCs feed well in my Rossi 92 .357 carbine. I'd figured the SWCs might hang up during feeding, but they seem to be held at just the right angle to slip right into the chamber. (Testing was done with 3 dummy rounds, not live ammo.)

I got the 195 grain bullets because I thought it would be neat to try and duplicate the old .38 Special Super Police load, which had a 200 grain LRN at mild velocity. I wound up loading them over enough Unique, though, that they will only be shot in my .357s. If nothing else, they should make steel plates jump around nicely.

The Speer 158 LSWCHP loads should run about 850 FPS from a 4" barrel, very similar to the old FBI load. I can bump the powder charge up a little to get over 900 FPS but at +P pressures. These would be good for defense from any of my K-Frames, and should also work well in my J-Frame S&W Model 640.

To measure the powder charges I used both my Redding Model 3 measure and my RCBS Little Dandy. I don't like how Unique meters in the Redding, although it seems to meter a little more smoothly in the Little Dandy. In contrast, Universal Clays seems to meter very nicely in the Little Dandy -- smooth and extremely consistent. I haven't tried it yet in the Redding but I expect it to behave similarly.

Of course, the proof will be in the shooting of this ammo. I'm hoping to get to the range in the next week or two to dirty up some wheelguns.